Gas Furnace Venting Problems: Common Causes, Troubleshooting & G2 Exam Questions

Gas furnace venting is one of the most important areas of study for Ontario G2 gas technician certification. Understanding how combustion products are safely removed from appliances is essential for diagnosing furnace faults, recognizing dangerous conditions, and installing heating equipment correctly.
Whether you're preparing for the Ontario G2 exam or improving your field troubleshooting skills, this guide covers common gas furnace venting problems, pressure switch faults, condensate drainage issues, and important concepts from CSA B149.1:25.
Why Is Proper Gas Furnace Venting Important?
A gas furnace produces combustion gases that must be safely discharged outdoors through an approved venting system.
Improper venting can contribute to carbon monoxide hazards, combustion instability, equipment shutdowns, and potentially dangerous conditions inside a building.
A technician must understand not only the vent piping but also the appliance design, draft-producing equipment, combustion air supply, and building conditions.
Understanding Common Furnace Venting Systems
1. Natural-Draft Venting
Natural-draft appliances rely primarily on buoyancy created by hot combustion gases to move those gases through the venting system.
These appliances can be particularly vulnerable to chimney problems, improper vent sizing, and building depressurization.
2. Fan-Assisted Venting
Many gas furnaces use an induced-draft fan to assist in moving combustion products through the heat exchanger and venting system.
The appliance may use a pressure switch or other proving device to verify that specified operating conditions have been achieved.
3. Condensing Furnace Venting
High-efficiency condensing furnaces recover additional heat from combustion gases, causing water vapour to condense within the system.
These appliances require approved venting materials and a properly designed condensate drainage arrangement.
Vent material, diameter, equivalent length, slope, support, termination, and jointing requirements must follow the furnace manufacturer's installation instructions and applicable codes.
Seven Common Gas Furnace Venting Problems
1. Blocked Exhaust Vent
Snow, ice, leaves, debris, or animal nesting can restrict an exhaust termination.
Symptoms may include ignition failure, pressure switch fault codes, or unexpected furnace shutdowns.
The correct response is to investigate the venting system and determine whether an obstruction exists, rather than immediately replacing a pressure switch.
2. Blocked Combustion Air Intake
On appliances with a dedicated outdoor combustion air intake, an obstruction can interfere with normal operation.
Snow accumulation and ice formation around low-mounted terminations can be particularly important during Ontario winters.
3. Incorrect Vent Pipe Slope
Some condensing furnace vent systems require a specified slope to direct condensate toward the appliance's drainage system.
An incorrect slope can allow water to accumulate in an unintended location, potentially restricting vent flow.
The required slope must be verified against the specific manufacturer's instructions. Do not assume all appliances use an identical vent slope or drainage arrangement.
4. Restricted Condensate Trap or Drain
A partially blocked condensate trap or drain line may cause water to accumulate inside the furnace.
On certain furnace designs, this can affect pressure proving and result in repeated shutdowns.
Technicians should inspect the drain system and confirm proper operation using the manufacturer's prescribed procedures.
5. Pressure Switch Not Closing
A pressure switch fault does not automatically mean the switch itself is defective.
Possible causes include:
Restricted exhaust or intake piping.
Condensate accumulation.
Damaged or disconnected pressure tubing.
Obstructed pressure sensing ports.
Inducer motor or housing problems.
A faulty pressure switch.
The proper diagnosis requires testing the complete system rather than replacing components based solely on the fault code.
Never bypass a pressure switch or other safety control to operate a furnace.
6. Excessive Vent Length or Incorrect Fittings
Vent systems have design limitations.
The actual vent pipe diameter, length, fitting types, and number of elbows can affect resistance to combustion gas flow.
Where the manufacturer specifies equivalent-length calculations, fittings must be accounted for according to those instructions.
A vent system that exceeds the approved design limits may prevent correct appliance operation.
7. Improper Vent Termination
Vent termination location affects safe operation.
A termination may be subject to restrictions involving building openings, air intakes, grade level, snow accumulation, other terminations, or additional site conditions.
Ontario installations must follow the applicable provisions of CSA B149.1:25, Ontario amendments, and approved manufacturer instructions.
How to Troubleshoot a Furnace Pressure Switch Fault
A logical diagnostic approach helps avoid unnecessary part replacement.
Step 1 — Identify the fault code
Read the furnace diagnostic code and compare it against the correct manufacturer's service literature.
Step 2 — Inspect the venting system
Check accessible venting and termination components for obstruction, damage, separation, or other visible defects.
Step 3 — Evaluate condensate drainage
For a condensing furnace, inspect the trap and drainage system according to the appliance service instructions.
Step 4 — Inspect pressure tubing and sensing connections
Look for disconnected, damaged, obstructed, or water-filled tubing where applicable.
Step 5 — Verify inducer operation and pressure
Qualified technicians may use an appropriate manometer and the manufacturer's test procedure to compare measured pressure with specified requirements.
Step 6 — Confirm correct operation
After corrective work, perform all required safety and operational checks, including appropriate combustion and venting verification.
If a hazardous condition is identified, follow the applicable shutdown, notification, and reporting requirements.
CSA B149.1:25 and Ontario Gas Venting Requirements
Ontario adopted CSA B149.1:25 with provincial amendments effective June 1, 2026.
For G2 exam preparation, students should become familiar with the code's venting provisions and how to locate the requirements applicable to a particular installation.
Important areas of study include:
Appliance venting categories and approved vent systems.
Venting materials and joining methods.
Vent sizing and installation requirements.
Termination requirements and clearances.
Common venting arrangements, where permitted.
Appliance installation instructions.
Combustion air and building depressurization.
Always verify the specific clause or table applicable to the question. Code provisions can vary by appliance type and venting system.
Ontario G2 Practice Exam Questions
These original practice questions are intended to test technical understanding. They are not official TSSA exam questions.
Question 1
A condensing furnace displays a pressure switch fault. Which condition should the technician investigate?
A. Incorrect thermostat display brightness
B. A blocked condensate drain
C. An oversized return air grille
D. A dirty indoor thermostat cover
Question 2
What is the purpose of the draft-inducer assembly in a typical induced-draft gas furnace?
A. To increase supply air temperature
B. To regulate incoming line voltage
C. To assist the movement of combustion gases
D. To control the circulating blower speed
Question 3
Why must vent piping on a condensing furnace be installed with the manufacturer's specified slope?
A. To increase gas manifold pressure
B. To manage condensate drainage correctly
C. To reduce thermostat cycling
D. To increase room ventilation
Question 4
A pressure switch does not close during the furnace startup sequence. What is the most appropriate initial approach?
A. Permanently jumper the switch
B. Replace the furnace control board
C. Increase manifold gas pressure
D. Investigate the proving circuit and possible draft restrictions
Question 5
Which documentation should be consulted when determining the permitted equivalent vent length for a furnace?
A. The specific furnace manufacturer's installation instructions
B. The thermostat operating manual
C. The homeowner's utility bill
D. A generic chart for all furnaces
Study Tips for Ontario G2 Certification
Venting questions often require students to connect several concepts.
For example, a question about a pressure switch may actually test your understanding of an obstructed vent, a blocked condensate drain, or improper equipment installation.
To prepare effectively:
Understand the differences between natural-draft, induced-draft, and direct-vent appliance arrangements.
Learn the typical sequence of operation for a modern gas furnace.
Practise interpreting furnace fault codes and manufacturer service documentation.
Understand how vent restrictions can affect appliance safety controls.
Become comfortable locating requirements within CSA B149.1:25.
Prepare for Your G2 Exam With GasTechnician.ca
GasTechnician.ca provides Ontario-focused study materials and practice exams designed to help candidates strengthen their technical knowledge.
Our G2 study resources cover advanced gas appliances, venting, electrical controls, combustion, diagnostics, and other important areas of exam preparation.
Explore:
Related GasTechnician.ca Study Guides
Final Thoughts
Gas furnace venting problems require a systematic approach.
A blocked vent, improper condensate drainage, or pressure switch fault can result in similar symptoms, but each condition requires its own diagnosis.
For Ontario G2 candidates, understanding why an appliance fails is just as important as knowing which component is involved.
Develop strong code-navigation, electrical troubleshooting, and combustion-system knowledge to become better prepared for both the certification exam and real-world service calls.
References: CSA B149.1:25 and applicable Ontario amendments; Ontario Regulation 212/01; furnace manufacturer installation and service literature.
This article is provided for educational purposes. Gas appliance servicing and installation
must be performed by appropriately qualified personnel. GasTechnician.ca is an independent study resource and is not affiliated with or endorsed by TSSA or CSA Group.



