top of page

Refrigeration Cycle Explained: Ontario 313A & 313D Exam Study Guide

4 hours ago
7 min read
tech checking ac pressures

Understanding the refrigeration cycle is one of the most important fundamentals for refrigeration and air-conditioning technicians.


Whether you're preparing for the Ontario 313A Refrigeration and Air Conditioning Systems Mechanic examination or the 313D Residential Air Conditioning Systems Mechanic examination, you need to understand how refrigerant moves through a system, changes state, absorbs heat, and releases heat.


The refrigeration cycle is the foundation of residential air conditioners, heat pumps, commercial refrigeration equipment, and many other cooling systems.


This guide explains the four main components, high- and low-pressure sides, refrigerant states, and common exam questions.



1. What Is the Refrigeration Cycle?


The refrigeration cycle is a process that transfers heat from one location to another using a circulating refrigerant.


In a typical residential air-conditioning system, heat is absorbed from indoor air and rejected to the outdoor environment.


The system does not create cold. Instead, it uses electrical energy to move heat against its natural direction of flow.


Most conventional air conditioners use the vapour-compression refrigeration cycle.


The basic system has four main components:


  1. Compressor

  2. Condenser

  3. Metering device

  4. Evaporator


These components form a closed refrigerant circuit.


2. The Four Main Components


Compressor


The compressor circulates refrigerant and maintains the pressure difference necessary for the refrigeration cycle.


In a typical operating system, low-pressure, superheated refrigerant vapour enters the compressor through the suction line.


The compressor raises the refrigerant's pressure and temperature before sending it toward the condenser.


Exam tip: The compressor is designed to compress vapour, not liquid refrigerant. Liquid entering a compressor can cause serious mechanical damage.


Condenser


The condenser is the heat-rejection component.


Hot, high-pressure refrigerant vapour enters the condenser and transfers heat to the surrounding air or another cooling medium.


As heat is removed, the refrigerant first cools toward its condensing temperature and then changes from vapour to liquid.


Further cooling may produce subcooled liquid.


In cooling mode, the outdoor coil of a conventional residential split air conditioner acts as the condenser.


Metering Device


The metering device creates a restriction that controls refrigerant flow into the evaporator and produces a pressure drop.


Common examples include:


  • Fixed orifice or piston

  • Capillary tube

  • Thermostatic expansion valve (TXV)

  • Electronic expansion valve (EEV)


As high-pressure liquid refrigerant passes through the metering device, its pressure decreases.


A portion of the liquid flashes into vapour, cooling the remaining refrigerant mixture to a lower saturation temperature.


Important: The metering device does not mechanically pump refrigerant. It controls flow and creates the pressure reduction needed for low-temperature evaporation.


Evaporator


The evaporator is the heat-absorption component.


Low-pressure refrigerant enters the evaporator as a mixture of liquid and vapour in a typical direct-expansion system.


Heat from the conditioned air or other load is absorbed by the refrigerant.


The remaining liquid evaporates as it absorbs heat.


Near the evaporator outlet, the refrigerant is normally vaporized and may gain additional sensible heat, creating superheated vapour.


The refrigerant then returns to the compressor.


3. Refrigerant Flow Sequence


A conventional vapour-compression refrigeration system follows this sequence:


Compressor → Condenser → Metering Device → Evaporator → Compressor


In a residential split-system air conditioner, the refrigerant also travels through the connecting line sets between the indoor and outdoor equipment.


The discharge line carries high-pressure, hot vapour from the compressor toward the condenser.


The liquid line carries high-pressure liquid toward the metering device under typical operation.


The suction line returns low-pressure vapour toward the compressor.


The exact component locations vary with system design.


4. High-Pressure Side vs. Low-Pressure Side


The compressor and metering device separate the refrigeration circuit into high-pressure and low-pressure regions.


High-pressure side

Low-pressure side

Compressor discharge

Metering-device outlet

Condenser

Evaporator

Liquid line before metering

Suction line

Higher saturation temperature

Lower saturation temperature

Pressure and temperature are closely related when a refrigerant is at saturation.

Increasing the pressure generally increases the saturation temperature of the refrigerant.


Reducing the pressure lowers its saturation temperature.


This relationship allows refrigerant to evaporate at a low temperature indoors and condense at a higher temperature outdoors.


5. Understanding Refrigerant States


Refrigerant changes state as it moves through the system.


Superheated Vapour


Superheated vapour is refrigerant vapour at a temperature above its saturation temperature at the measured pressure.


It is commonly found leaving the evaporator and entering the compressor.


Saturated Vapour


Saturated vapour is refrigerant at its saturation condition, where condensation can begin if heat is removed at constant pressure.


Saturated Liquid


Saturated liquid is refrigerant at its saturation condition, where evaporation can begin if heat is added at constant pressure.


Subcooled Liquid


Subcooled liquid is refrigerant at a temperature below its saturation temperature at the measured pressure.


It is commonly found near the outlet of a properly operating condenser.


Liquid-Vapour Mixture


A mixture of liquid and vapour is typically present immediately downstream of the metering device and within part of the evaporator.


Understanding these states is essential for interpreting refrigeration system pressures and temperatures.


6. What Is Superheat?


Superheat is the temperature of refrigerant vapour above its saturation temperature at a given pressure.


The basic formula is:


Superheat = Actual vapour temperature − Saturation temperature


For example:


  • Suction-line temperature: 55°F

  • Corresponding dew-point saturation temperature: 40°F


Superheat = 55 − 40 = 15°F


Superheat helps technicians evaluate refrigerant conditions and, when combined with other measurements, investigate evaporator operation.


For blended refrigerants with temperature glide, use the appropriate dew-point value when calculating vapour superheat.


Superheat should not be interpreted independently of system conditions or manufacturer guidance.


7. What Is Subcooling?


Subcooling describes how far the temperature of liquid refrigerant is below its saturation temperature at the measured pressure.


The formula is:


Subcooling = Saturation temperature − Actual liquid temperature


For example:


  • High-side bubble-point saturation temperature: 105°F

  • Liquid-line temperature: 95°F


Subcooling = 105 − 95 = 10°F


Subcooling can help evaluate condenser and liquid-line conditions.


For refrigerant blends with temperature glide, use the appropriate bubble-point value for liquid subcooling.


The desired value depends on the equipment design and manufacturer specifications.


8. Fixed Orifice vs. TXV Systems


Two common residential air-conditioning metering arrangements are fixed orifice and TXV.


Fixed-Orifice Systems


A fixed orifice provides a calibrated restriction.


Refrigerant flow depends on operating conditions, including the pressure difference across the metering device.


When evaluating charge, technicians commonly use manufacturer-provided superheat procedures on appropriate fixed-orifice systems.


TXV Systems


A thermostatic expansion valve modulates refrigerant flow in response to the superheat condition sensed at the evaporator outlet.


This helps maintain a controlled degree of superheat across changing operating conditions.


Appropriate TXV system charging procedures commonly rely on manufacturer-specified subcooling targets.


Exam tip: Do not assume that all fixed-orifice systems have the same target superheat or that every TXV system uses the same subcooling target.


9. Heat Transfer in the Refrigeration Cycle


The refrigeration cycle transfers heat in three important stages.


Evaporator: Heat enters the refrigerant from the space or material being cooled.


Compressor: Mechanical work is added to the refrigerant.


Condenser: Heat is released from the refrigerant to the surrounding environment.


For a steady-state system, the condenser typically rejects the heat absorbed by the evaporator plus the work added by the compressor.


This explains why an air-conditioning condenser releases more heat than the evaporator absorbs.


10. Common Refrigeration Cycle Problems


Restricted Airflow Across the Evaporator


Reduced indoor airflow can decrease the evaporator load and contribute to low suction pressure, reduced capacity, and coil icing under some conditions.


Dirty Condenser Coil


Insufficient condenser heat rejection can increase condensing temperature and pressure.


Refrigerant Undercharge


Loss of refrigerant may cause poor capacity, reduced liquid-line subcooling, and elevated superheat, depending on system type and operating conditions.


Metering Device Restriction


A restriction can reduce refrigerant flow into the evaporator, producing symptoms associated with a starved evaporator.


Compressor Problems


A damaged or inefficient compressor may be unable to maintain the expected system pressure differential.


Important: No single pressure or temperature reading is sufficient to diagnose every refrigeration problem. Technicians must consider airflow, operating conditions, equipment design, and several measurements together.


11. Refrigeration Cycle Practice Exam Questions


These original questions are intended for Ontario 313A and 313D study. They are not official Skilled Trades Ontario examination questions.


Question 1


What is the primary function of the compressor?


A. To remove moisture from indoor air

B. To circulate refrigerant and raise its pressure

C. To directly cool the liquid line

D. To reduce refrigerant pressure entering the evaporator


Question 2


Where does refrigerant normally reject heat in cooling mode?


A. Suction line

B. Metering device

C. Condenser

D. Evaporator


Question 3


What is the primary function of the metering device?


A. To control refrigerant flow and create a pressure drop

B. To compress refrigerant vapour

C. To remove heat outdoors

D. To increase refrigerant pressure


Question 4


A refrigerant has a dew-point saturation temperature of 40°F and a measured suction-line temperature of 55°F. What is the superheat?


A. 10°F

B. 20°F

C. 95°F

D. 15°F


Question 5


Which component normally absorbs heat from indoor air in a residential air conditioner operating in cooling mode?


A. Compressor

B. Evaporator

C. Condenser

D. Liquid-line filter drier


Question 6


What is the typical refrigerant condition entering the compressor in a conventional properly operating direct-expansion system?


A. High-pressure liquid

B. Low-pressure liquid

C. Low-pressure superheated vapour

D. Saturated high-pressure liquid


Question 7


A refrigerant has a bubble-point saturation temperature of 105°F and a measured liquid-line temperature of 95°F. What is the subcooling?


A. 10°F

B. 15°F

C. 20°F

D. 200°F


Question 8


What is a common consequence of reduced condenser airflow?


A. The system automatically produces more cooling capacity

B. The refrigerant stops circulating in every case

C. The evaporator pressure always increases

D. Condensing temperature and pressure may increase


12. How to Study the Refrigeration Cycle for the 313A and 313D Exams


Start by memorizing the correct sequence of the four main components.


Next, learn which components operate on the high-pressure side and which operate on the low-pressure side.


Then focus on refrigerant state changes.


You should be able to identify where the refrigerant is normally vapour, liquid, or a liquid-vapour mixture.


Once those concepts are clear, practise superheat and subcooling calculations.


Finally, apply the principles to common troubleshooting scenarios.


For more advanced 313A preparation, continue with pressure-enthalpy diagrams, system capacity, compressor efficiency, refrigerant properties, and additional refrigeration-system configurations.


13. Prepare for Ontario 313A and 313D Exams


GasTechnician.ca provides Ontario-focused refrigeration and air-conditioning study resources.


Our practice examinations help candidates review technical concepts, electrical systems, controls, refrigeration fundamentals, and troubleshooting.

Explore:


Understanding the refrigeration cycle is essential for both examination preparation and professional HVAC troubleshooting.


The compressor raises refrigerant pressure, the condenser rejects heat, the metering device creates a pressure drop, and the evaporator absorbs heat.


These four components work together to transfer heat from one location to another.

For Ontario 313A and 313D candidates, mastering refrigerant states, high- and low-pressure sides, superheat, and subcooling provides a strong foundation for more advanced refrigeration topics.


Technical references:


  • Copeland — Refrigeration Basics: Understanding the Refrigeration Cycle.

  • Copeland — Refrigeration Basics: A Look at Each Step of the Refrigeration Cycle.

  • Trane — Refrigeration Cycle.

  • Skilled Trades Ontario — 313A and 313D trade training standards.


GasTechnician.ca is an independent educational resource and is not affiliated with or endorsed by Skilled Trades Ontario, Copeland, or Trane. Refrigeration work must be performed by appropriately qualified personnel.

Test Your Knowledge with Free Practice Questions

made-in-canada.png
DMCA-protected.png
  • Instagram
  • Facebook
pstudyguides.png
paypal-verified.png
excellent-customer-service (1).png
12087987_977754352277347_787474696537681
Trust-pilot-Reviews.avif

 © 2026 gastechnician.ca

bottom of page